Steps Necessary To Pass The NS0-176 Exam from Training Expert Pass4cram
Valid Way To Pass Cisco and NetApp FlexPod's NS0-176 Exam
NEW QUESTION 46
Which set of commands maps VLAN 100 to VSAN 100?
- A. Nexus 5000-A#configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-A (config)# vsan 100 Nexus 5000-A (config-vsan) # fcoe vsan 100
- B. Nexus 5000-B# configure terminal Nexus 5000-B(config-vsan) # vlan 100 Nexus 5000-B (config-vsan)# vsan 100 name vsan100
- C. Nexus 5000-B# configure terminal Nexus 5000-B (config) # vsan database Nexus 5000-B (config-vsan)# vsan 100 Nexus 5000-B(config- vsan) #vsan 100 name FCoE-VLAN 100
- D. Nexus 5000-A#configure terminal Nexus 5000-A (config) # vlan 100 Nexus 5000- A (config-vlan_ #fcoe vsan 100
Answer: D
NEW QUESTION 47
While working on a performance related issue on your FlexPod solution, you notice an unequal distribution of traffic over the physical interfaces of a four port vPC between two Nexus 5000 switches. You would prefer a more even traffic distribution.
Which command would you use to accomplish this task?
- A. ~port-channel load-balance ethernet~
- B. ~hardware multicast hw-hash~
- C. ~lacp rate fast~
- D. ~lacp system-priority~
Answer: A
NEW QUESTION 48
An administrator has a FlexPod solution using VMware vSphere 6.0. The ESXi hosts use iSCSI for storage connectivity, and all paths have been configured and connected between the NetApp cluster and the ESXi hosts.
Virtual Storage Console has been installed and ESXi host-recommended settings have been applied to all hosts. The active LUN path for one of the iSCSI datastores experiences a connectivity failure and the LUN switches to a new active path.
In this scenario, which event would trigger the ESXi host to switch the active LUN path again?
- A. The ESXi host scans for new VMFS datastores.
- B. The NetApp LIF is reverted to its home port.
- C. The original LUN path comes back online.
- D. The host processes 1,000 I/O operations.
Answer: B
NEW QUESTION 49
Given the following switch output, where would you expect see notification level messages?
N5K-1# show logging info.
Logging console: enabled (Severity: error)
Logging monitor: enabled (Severity: informational)
Logging linecard: enabled (Severity: emergency)
Logging fex: enabled (Severity: notifications)
Logging time stamp: seconds
Logging server: disabled
Logging logfile: enabled
- A. On the console
- B. On the terminal sessions
- C. On the linecard
- D. Notification messages will not be seen anywhere
Answer: B
NEW QUESTION 50
You are installing two NetApp FAS8080 EX controllers.
Which two ports would you use for HA connectivity? (Choose two.)
- A. ib0b
- B. eof
- C. e0e
- D. ib0a
Answer: A,D
NEW QUESTION 51
You are asked to configure the computer resources in a FlexPod solution to ensure that jumbo frames are configured end-to-end.
Which three actions must you perform to accomplish this task? (Choose three.)
- A. Set the MTU size to 1500 on the vNIC template
- B. Configure a UCS QoS System Class with the jumbo frames.
- C. Enable jumbo frames on all of the switches between the initiator and the iSCI target.
- D. Configure jumbo frames on the switch VLANs.
- E. Enable jumbo frames on the operating system adapter.
Answer: B,C,E
NEW QUESTION 52
Exhibit:
You are configuring iSCSI boot from SAN on your UCS blades.
Referring to the exhibit, how many paths will there be to the Boot LUN?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION 53
You want to run the FlexPod execution profile in NetApp Config Advisor.
Which three login credentials are required to perform this task? (Choose three.)
- A. ESXi server
- B. NetApp cluster
- C. NetApp support login
- D. UCS Manager
- E. Nexus switches
Answer: B,D,E
NEW QUESTION 54
Exhibit:
Which Cisco switch is shown in the exhibit?
- A. Nexus 5548
- B. Nexus 2232
- C. Nexus 5596
- D. Nexus 7004
Answer: A
NEW QUESTION 55
You are asked to increase read performance for a single aggregate; however, there are no PCI-e slots available in the NetApp cluster nodes.
In this scenario, which feature meets these requirements?
- A. Thin Provisioning
- B. Advanced Drive Partitioning
- C. Flash Cache
- D. Flash pool
Answer: D
NEW QUESTION 56
When using Clustered Data ONTAP 8.1 and later, what is the default for new aggregates?
- A. 64-bit aggregates
- B. 32-bit aggregates
- C. 128-bit aggregates
- D. traditional aggregates
- E. cluster aggregates
- F. Vserver aggregates
Answer: A
NEW QUESTION 57
Which service may be used to manage users and groups in a vSphere environment?
- A. Network Time Protocol (NTP)
- B. Microsoft Active Directory (AD)
- C. VMware vSphere Storage APIs for Array Integration (VAAI)
- D. Domain Name System (DNS)
Answer: B
NEW QUESTION 58
An administrator is trying to present an NFS datastore to an ESXi host.
Which two must be available before mounting? (Choose two.)
- A. host name case sensitivity
- B. export policy access
- C. datastore name case sensitivity
- D. junction path case sensitivity
Answer: A,B
NEW QUESTION 59
Which server role is required to support running virtual machines on a Microsoft based hypervisor?
- A. Web Server
- B. Hyper-V
- C. Application Server
- D. Remote Access
Answer: B
NEW QUESTION 60
Which two are correct about VSAN configuration within UCS Manager? (Choose two)
- A. In addition to SAN tab, VSANs can be configured under UCSM Server tab as well.
- B. VSAN can be configured as fabric interconnect specific.
- C. VSAN can be configured as a global parameter.
- D. VSAN IDs 3840-4079 are not available regardless of the Fabric Interconnect mode.
- E. We can delete VSAN 1.
- F. VSAN ID and FCoE VLAN ID have to match.
Answer: B,E
NEW QUESTION 61
What are two valid cluster interconnect switches? (Choose two.)
- A. Cisco Nexus 9504
- B. Cisco Nexus 5596
- C. NetApp CN610
- D. Cisco Nexus 7004
Answer: B,C
NEW QUESTION 62
Which tool can be used to validate hardware installation in a FlexPod solution?
- A. Cisco UCS Director
- B. NetApp OnCommand Insight
- C. NetApp OnCommand Unified Manager
- D. Cisco UCS Central
- E. NetApp Config Advisor
Answer: E
NEW QUESTION 63
The NetApp Vistual Storage Console is used to set which three setting categories on ESXi hosts? (Choose three.)
- A. MPIO Settings
- B. Adapter Settings
- C. Logging Settings
- D. NFS Settings
- E. Security Settings
Answer: A,B,D
NEW QUESTION 64
Your customer has the storage configuration for a FlexPod solution shown below.
- FAS8040 HA-pair
- Disk stack one-4x DS4243 disk shelves (2TB SATA disk drives)
- Disk stack two- 2x DS 2246 disk shelves (1.2TB disk drives)
- There are no unused SAS ports on either controller
- There are no expansion slots available on either controller
The customer wants to attach a single DS2246 disk shelf with 800 GB SSD drives.
In this scenario, what are two ways to connect the new shelf for optimal performance? (Choose two).
- A. Cable the new shelf to the end of stack two.
- B. Cable the new shelf to the end of stack one.
- C. Cable the new shelf to the beginning of stack two.
- D. Cable a new stack for the SSD shelf.
Answer: C,D
NEW QUESTION 65
Which backup type stores Service Profile information as a small editable file?
- A. Logical Configuration
- B. All Configurations
- C. Full Backup
- D. System Configuration
Answer: A
NEW QUESTION 66
Which type of pools do you need to create vHBA templates?
- A. MAC
- B. IQN
- C. WWNN
- D. WWPN
Answer: D
NEW QUESTION 67
How many cluster interconnect switch(es) are required for a 4-node NetApp cluster?
- A. 0
- B. 1
- C. 2
- D. 3
- E. 4
Answer: D
NEW QUESTION 68
......
All NS0-176 Dumps and Cisco and NetApp FlexPod Implementation and Administration Training Courses: https://www.pass4cram.com/NS0-176_free-download.html